How to wind the fishing line on the trimmer: examples and recommendations

As a rule, it is necessary to check all the gear, the reliability of the connecting loops and hooks sharpness before leaving on a fishing trip. But do not forget about the backing that is wound onto the spool, because of how the wind on the fishing line trimmer, will depend on the success of fishing as a whole. Incorrectly wound, it can lead to a "beard", which is quite difficult to unravel, and that takes a huge amount of precious time casting distance can be significantly reduced, and even in such a situation it is better not to fish.

Selection of coil

Novice fishermen of their inexperience pay little attention to the selection of fishing rods and tackle, and in fact choose the right equipment - is the key to fishing success. Typically acquire coil bobbin with a size of from 2000 to 3000, which can accommodate up to 100 meters of line numbers 0, 2 to 0, 3 mm.

In addition to size, they differ from each other by way of the winding on the spool. Wind the line onto the reel trimmer can be straight, cylindrical and tapered styling, it all depends on the model. Also pay attention to the country of origin of fishing gear. If the coil is of Chinese origin, from a cheap series always be prepared for the entanglement of fishing line when casting and the emergence of the "beard", in addition, cheaper option rather quickly breaks down and needs repair or replacement.

When winding quality fluorocarbon should form strictly parallel relative to the bobbin laying the direct winding method, and oblique with cone.

How to fix the thread trimmer to

Winding a fishing line on the trimmer - is simple enough, but it requires some skill. First we need to firmly fix the coil on the rod. Then one end of the fluorocarbon to thread through all the tabs and secure the rod to the spool. To do this, raise the handle of the coil wrapped around a fishing line and tie a knot Arbor.

If the thread is hard or thick, before winding it should be dipped in warm water, after this procedure, it becomes elastic and smooth lie. When winding is desirable that was an assistant who would keep a supply of fishing line. In the process should slow down slightly fluorocarbon finger or a soft cloth.

What should be the length of the working yarn

It all depends on the method of fishing and pond. If you need to catch a small length of line, it should be less if further zabroska, the fluorocarbon need more. For a quick change in field conditions each fisherman must know how to change the line trimmer. If deep coil bobbin, approximately two thirds of the need to fill a cheaper yarn, the remaining portion of the working reel fluorocarbon required directly for fishing. Preroll should consist of a thin fishing line, rather than working, it will increase the density of the core, and not to fall.

How to wind the fishing line on the trimmer

During the winding reel handle should be to turn smoothly, without jerks and at high speeds. It is necessary to ensure that the thread lay in neat parallel lines. It should not be too thick to wind the fishing line is not provided for this coil.

Gently winding fluorocarbon, attention should be paid, how much is left up to the rim. The optimal distance - is 2 mm from the upper layer to the rim edge.

Backing

Every fisherman must know how to wind the fishing line on the trimmer and what is the backing. Backing - a preroll on the coil bobbin. For this purpose, use is often thread diameter of 0, 1 to 0, 3 mm. If the take-up use a thicker fluorocarbon, it can lead to uneven and irregular laying the main line. It is undesirable to use the backing material is wet, to such include nylon yarns and cotton. They are unable to for a long time to dry completely, leading to debate and replacement of fishing line on the trimmer - is the additional financial costs.

The amount of yarn needed for Buckingham, can only be determined empirically. This will require two spools. One first required amount of wound fishing line working, and then the backing is wound so that the edges of the collar to the left two millimeters. After this procedure, the bobbin wound with fluorocarbon removed and put on a blank, which is wound thread, but in the reverse order - first the backing, then the working nylon.

Storage nylon thread on a spool

How to wind the fishing line on the trimmer - understood, now let's talk about the storage of fishing gear, particularly fluorocarbon on the spool. For long life filament should follow a few rules, the implementation of which allows you to save money on the purchase of new equipment.

It is important to remember that after the fishing line and fishing reel parts become wet, they should be well dried. Poorly dried fluorocarbon preet very fast and becomes unusable. It becomes brittle and may break at the crucial moment. To avoid this, after the seasonal fishing line from the reel to be rolled up and spread out on the floor so that it is well dried. This procedure should be carried out with the backing (pre-roll). Drying nylon thread can be and after each fishing if you go at it once a month.

You already know how to change the line on the trimmer, it does not take much. Always store your fishing tackle in a dry place, it will become a guarantee of reliability and durability.