Ways to attach the float to the line

One of the most popular types of fishing - a fishing rod with a float, so-called float rod. The fishing line to a fishing rod should be selected taking into account the weight of the fish you want to catch. Since the rod is used float, then to the line necessarily need to attach the float. Fix it in several ways. About them useful to know both novice and have already mastered the basics of fishing. Selection of the float construction and its method of fixing to the line depends on the method of fishing. But still, how to anchor the float to the line right? About it and tell our article.

The main requirements to the float

It is important that when casting the float, he did not produce bursts, thereby posing and frightening the fish. He is obliged to justify its name, it has to be light enough to hold in the water well and the float must have the necessary capacity. How to attach the bobber to the fishing line? It must be done in such a way that the hook is located at the desired depth.

There are two main ways of tying float to the line:

• Fixing the blind.
• Mounting moving.

Their difference will talk further.

The blind fastening

How to fix the float to the line? This method of mounting is used in almost all the tooling for float fishing rod. By choosing this secure method, you yourself determine the distance at which the float should be. On a scaffold in this case it does not move. There are different types of blind fasteners, which are dependent on the number of mounting points. There may be one or two.

fastening point a

How to attach the bobber to the fishing line? This single-point method is for standing waters and another for oblavlivaniya snags. The peculiarity of such fasteners is that the float is less clinging. We are talking about the use of floats Waggler group whose attachment point is only at the bottom, that is, for the keel. A float of this type is used as a further sliding. And attach it in such ways:

• The ring float insert the wire. The ends curl, treat needle files. And we put on the resulting twisting of tubing and line.
• Use a thick wire that is inserted into a loop in the float ring. At each end of the wire is put on one tubing.

On the line tubing must be worn before the tooling. In addition, he must cling to fishing process does not overshadow their slipping.

If you are using a heavy float, then it is necessary to use a special mounting fixture, which involves the use of a metal sleeve or Teflon core.

Points of fasteners two

If a fish is caught on the water over, the float must be fixed for the two points. Due to the fact that the float rod for accessories used soft woods, it needs to be fixed in a certain sequence in order to prevent twisting of the fishing line. There are three designs, involving a double fixture:

• First Pole Floats - lower point. This design is done so. Dress keel lower tubing. For the keel, he should act on 23 mm, to avoid friction. Determine the length of fishing line, which should be deleted in view of the hook. We fix the line by two more cambric. So we all get three cambric. You can, of course, use only two, but three still more reliably.
• The second Pole Floats - top point. In this case the fastening of the float to the line is carried out for a spring, which is more preferred, or a ring.
• Third Stick Floats - unlike in different diameters keel. Fasten the bottom point of using only one tubing. Assigned to the spring. In her absence we put sleeve on the antenna, namely its thin part. To enhance the connection tubing glue. But as mentioned earlier, the spring is still better.

sliding attachment

How to attach the bobber to the fishing line? As the name implies, in this case the float is movable along the fishing line (slide). What is it for? The bottom line is to make a sliding float helped throw into the depths. This snap-in is designed for fishing at a depth of three meters and long casts, at distances up to 40 meters. But when using a snap of the rod length should be small.

The design of the sliding float

Such float differs oval shape at its end located somewhere in 30-cm dish, which looks completely out of the water. She will be painted in a bright color. That part of the float, which should be located under water, colorless and called her keel. In a special antenna located ring (ear), which serves for attachment of fishing line. How to tie a float with eyelet? It is important to remember that the line never with a ring is not directly connected, but this is done by means of a swivel. This connection makes it possible to quickly detach the float if necessary. This method of fixing does not allow gear twisted, even when the fishing line slides on the float. Also plays an important role right ogruzhennost float. Ogruzka allows him to send in the necessary place and hold it upright in the water.

When ogruzke built into the body of the float effect is enhanced by 1-2 Balis, just below the crimped on the line. In the absence of such ogruzki weight at the bottom need to wind the additional washers, because the lungs are not able to work floats. There are four ways to fix the sliding float. About them and talk.

Two locking unit

How to tie a float to the line? Appliances such fastening next. The ring is passed the line. On both sides are put two plastic beads (stoppers), and the fishing line section (and float thereon will slide) is limited by two locking assemblies. The stops are necessary to nodes are not stuck in the ring. In addition, components made strong, as when casting float your weight puts pressure on the lower assembly.

Types of locking knots

How to fix the float to the line? As mentioned above, this can be done by locking knots. For catching fish with a float stopper assemblies are used most often are formed of yarns (preferably woolen) or of monofilament fishing line, and fastened on top of the main line. When this is applied a sliding float with one or two point fastening. And most of the stopper - the top. It is intended to set the float is released. That is why the stop should move with some force on the main line. In addition, the stick when casting equipment in crossing the rings he should not. Mandatory requirement - the node after tightening does not deform the main fishing line. There are two types of lock assemblies.

• Node "Clinch". To tie it, you need to take a 25-30-cm segment of monofilament fishing line diameter it should be like a main line or a bit more. Adds cut in half, placed under the main fishing line, presses his fingers. Perekinem through the main line and the working end of the segment. As a result, the main fishing line will be formed inside the fishing line. We make around the main line and the auxiliary end of five turns of the working end, the need to hold the finger loop formed on the main line. Skipping to the working end of the loop. Gently pull up the ends of the pre-moistened with saliva node. Cut off the excess fishing line lock to the ends left by a half to two centimeters. You can not worry about sticking the ends do not become a hindrance for the passage through the crossing node of the ring of the rod. Moreover, for them it is possible to tighten the locking assembly, when it weakens, moving along the main line.
• Node "Duncan." We need to take a segment monofilament fishing line with a length of 25-30 cm in diameter as well as the main line, or a little more. Let auxiliary end pyatisantimetrovym length under basic scaffold, the working head end of it and push fingers formed in such a way to the main loop. It should leave the working end of a 10-centimeter long. Summing the working end below the main line, and start it, and the loop winding. Making four turns around the working end of the main line and loops summarize it in a loop. Wettable saliva node for delaying its smooth working end, wherein the auxiliary holding arm end and the main fishing line. It should be done carefully, so that the locking assembly were extremely flat windings. Such a site will be easier to pass through the crossing of the ring of the rod from the previous node. But still form the assembly complex. You can take a piece of plastic tubing, such as "straws" for a cocktail, 7-10 centimeters long, to impose on it in advance several locking units of this type (preference should give wool threads). So you can save your time fishing, and you do not need to knit stops away.

Fixing using brackets

How to attach the float to the line? To limit the sliding movement of the float is a wire bail. it will also help to set the desired depth and give the float during fishing displaced. Compared with the first method in this case is much less entangled monofilament.

Fixing with ceramic retainer

How to attach the bobber to the fishing line? The latch must slide along the line. Be sure to put a stopper. This type of mount is designed for Waggler designs.

The line inside the float

How to tie a float to the line? This type of attachment is used for the floats, which contain inside a tube. It scaffold and inserted. Such a float used for fishing at depth. It is necessary to insert into the line, then put on the keel, then fix the line at the end of the keel by a cambric.

It can be concluded, to determine how to attach the float to the line, it is necessary to take into account the depth at which fishing will occur, set the distance casting and choose the way of fishing.