Floats for long casting. Homemade float for long casting

Performing long casting fishing difficult to implement. This requires not only the selection of special equipment, but also suitable conditions for fishing. If both conditions are met, you can count on a trophy in the form of large fish. Typically, for such purposes, use of match rods, allowing to work at great distances from the shore. But the key component is a sliding float for long casting, which is associated with the rod complicated shipping arrangements. Despite all the difficulties and nuances of implementing a fishing scheme, it is flexible and provides great opportunities for experimentation.

Features fishing with long casts

At first the fishermen practiced long casts using for. The water carried off the float at a certain distance, which made it possible to expand the coverage area of ​​fishing. However, modern technology make it possible to carry out casting in such a way that the distance from the float to exceed last match rod length. For this reason, a huge responsibility for the quality of the entire process of fishing assume floats for long casting, which determine, among other things, the behavior of most equipment. In particular, it is of great importance during the flight of aerodynamics and hydrodynamics in water. The importance of the float in this case due to the fact that it focuses the main fraction of the mass production.

Technique casting sliding float

Since the implementation of casting the float starts to pull all the rigging itself. Stops this process at the end of planning at the water surface, where the baton takes over the shipment. Ideally, there should be provided a snap stretch over the entire length, to lay it gently into the water. It is at this stage, many fans make mistakes. The fact is that the floats for long casting must create an arc with the correct flight path, which is achieved not by itself, but by the true fisherman coordinated action. For example, the excess path can cause that the snap-rotate toward or fall on the water at an angle. There is also a risk of a tie-in, as ogruzka in this case may lie directly on the float. Conversely, a low trajectory will lead to the fact that the snap-brainer hlyupnetsya and create a big splash.

The characteristics of the float for long casting

a unified approach to the manufacture of such floats do not exist, they vary in shape and size. Thus, the cylindrical shape of the model used for smaller distances, and casting in calm weather conditions. For them, the chosen ogruzka with minimum weight - usually no more than 5 grams. The body of such products has a diameter of 4-6 mm. But most often used for distance casting rod with a sliding float, which was extended to the lower part of the increase carrying capacity. This feature gives the snap-high stability and simplifying the very casting technique. Especially for long-range shots performance is the best option. Mass production is typically greater than 20 g, and the diameter of the float varies from 10 to 30 mm.

We should also consider the antenna parameters of the float. In diameter, it can be 5-6 mm and the length - 1/6 of the total product. sometimes also make stabilizing elements of Dacron on top to increase the stability.

Production of float

The lower part of this float is usually made of two parts - container and tip. They are made of stainless brass. The tip is a ball an average diameter of 5 mm. On the sides it grind to a thickness of about 2 mm. Next, at the site is formed an opening 3 mm in diameter. To homemade float for long casting served longer edges of all corners must be treated with countersink. Due to the openings will be obtained eyelet fishing line. It is important to bear in mind that the processing of the edges and the location of the hole will affect the aerodynamics of the float. Of course, in the future it will be possible to adjust its planning ability due ogruzki, but it is desirable to initially perform the processing quality of the product.

Options ogruzki

Now it is possible to consider further the question of how to ship float for long throw into the water. In this case, it can be used two solutions: concentrated ogruzka and distribution of additional weight on the basis of a garland. The pellets are used in a quantity of 4-5 pieces as sinkers. Their weight is typically less than 5 g, and a diameter of 3-5 mm.

Thus, a concentrated version of the arrangement suggests that Georgia will be located one after the other at a distance of 10-20 cm from the undershepherds. This scheme is suitable when using the solid rod and planned Krupnyakov fishing in deep water. Layout ogruzki garland, on the contrary, should be used when fishing shallow and where floats for long casting must dive safely and without a splash. The difference of such scheme is that the pellets are arranged apart at a distance of 3-5 cm.

to the requirements fishing rod

In general, it is driven by the same selection rules as in the spinning. Thus the rod should comprise suitable choke coil and a ring for him.

Optimal length is 3, 5-4 m, while the number of rings ranges from 12 to 16. As for the driving rod cast with the sliding float must provide even weight distribution and reduce the amplitude of the shock the fishing line on the surface of the rings, such equipment would be optimal. Choice of class rigidity and softness depend on fish for which hunting is planned. If you want versatility, the suit first-class models to vyvazhivat predators weighing up to 20 kg.

mating locking components

Usually knitted two locking assembly. Chief among them, in the upper part, serves to determine the level of the loading compartment floats sinkers. The spacing of pellets to float in this case must be at least 1, 5, the length of the latter. By the way, in this scheme, much depends on how the carried mount for casting floats far as it can be used a different number of fixing points. If the two fixing points are used, the third stopper knot tying may not be required. But to enhance the functionality of equipment and it can be done. In the process of fishing, he will allow to determine the distance required to take-up the fishing line after casting. It is necessary to deliver directly to the bait tackle zone. If you plan to supply the gear locking assemblies, it is necessary to consider another point. The fact that a sliding float for long casting must have the possibility of free flight, without interference. That's when the casting feature locking units can hamper the passage of fishing line through the rings. The solution may be only the acquisition of durable and high quality fishing line.

for long casting Tooling

Starting work should be knitted with a swivel to the line, wherein the thickness may be 0, 15-0, 2 mm. Since this is a long casts, then use ultra-thin fishing line is not necessary. Next, a stopper. It is important that equipment for long casting with float had elements of suitable diameters, so the elements of the shipment and the stopper must comply with the float. Fishing line is passed through the tube set and pellet elements stopper. At the end, if desired, you can snap swivel. This is one of the easiest ways to snap mounting, which can be used for long-distance casting. Unfortunately, it is suitable mainly for catching small fish sizes.

Conclusion

Fishing with long casting is complex, not only at the stage of preparation of equipment, but also in the implementation process. Important role in the success of this technique is played floats for long casting, of which the effectiveness of the entire snap-dependent. It may be asked how justified this method of fishing, given its complexity. On the one hand, the correct execution of long casting increases the chances of catching a big fish. On the other - the technique makes it possible to make it a variety of adjustments, making corrections on the fishing conditions, the behavior of fish, etc. For example, if the fishing jig substantially limits the fisherman, the technique long casting allows to adapt to different conditions, driving and depth, and characteristics.. snap.