Knots hook with a shovel, with a ring. Knotless knot to the hook

Fishing has always been and will remain exciting experience regardless of time or season. Of course, a good catch depends on properly prepared tackles. Especially important criteria are the nodes to hook the bait. This attribute of each fishing should be of high quality and very durable. It is therefore necessary to learn how to tie knots for hooks.

What you should pay attention to

Before you start to tie a knot, it is necessary to buy quality gear. It will depend on the strength and consolidate further the catch.

The most important thing - it is the sharpness of the hook. The hook must be sharp. In order to ensure that the hook does not dull the sting should be checked. This is usually done in two ways:

• Check the sharpness with your fingernail. To do this, putting a tip of the nail at an angle of 30-40 degrees and lightly presses. If the point of stupid, it just come off if the island, it would stick to the nail slightly and will remain in place.
• At home, with 8-fold magnifying glass. It is very easy. Point of the hook should be considered under a magnifying glass, if it is dull, it will be clearly seen.

Another criterion, which should also pay attention - this is fishing line. It should be durable and elastic. Also, do not choose too thick twine. It is better to buy the average diameter of the thread and not too noticeable in the water.

If they acquired high-quality gear in accordance with these criteria, it is possible to make high-quality components for the fishing line and hook.

to

Methods for knitting fishing line to a hook

So tackle all bought, now stands to start preparing. The first step is to make components for the hook. The first question that may arise - which is also the most durable components. This is especially true novice anglers. Ways of knitting fishing line to a hook, there are many, but the novice angler should be familiar with the most popular sites for the hook.

What are ways of fixing?

• Units for hooks with blades.
• Units hook with rings.
• knotless knots - to him also is attributed polomar nodes clinch improved.

Of course, this is not all of the nodes, but the most famous. If the knot exactly under the scheme, the result can be obtained durable and sturdy fixture.

Scheme crochet hook with the vane assemblies

In order to make components for the hook to the shoulder blade, you must choose the most durable unit. These hooks are best used Knutova node.

tying circuit consists of the following:

1. First, you need to make a noose and put it on the shank of the hook. It is advisable to leave a small piece of the free end of line by about 8 cm.
2. After that is done from the end of the fishing line loop. Then do 8 turns around the loop and in the loop skipping the end of line.
3. Node is well moistened with water.
4. At the end of the assembly is tightened. Hold the free end of the line and tighten.

During tying fishing line should run from the inside of the hook.

How do I make a knot with a ring?

In order to make components for the hook with a ring, should become familiar with the most popular ways of attachment. During tying everything should be done properly to the nodes to obtain a strong and sturdy.

Tying is as follows:

• To start from the fishing line should be make a small ring. Further, about three or four times through this ring is pushed the tip of the fishing line.
• Then, the ring should be tightened by means of the ends of the fishing line so that he will make two ringlet shape similar to the "eight". Further, through the ring received "eight" of the hook through the forearm.
• At the end cut the rest of the line, when it is necessary to leave the end of the fishing line to a length of 4 millimeters. Also, assembly can be done differently. For this line was previously is pushed into the hole on the hook and then made "eight". But in this case, "eight" is inserted through the tip of the hook.

Universal unit for the hook with a ring

This type of assembly also has good strength and very strong. Now it is necessary to consider how he tied:

1. threaded tip of the fishing line through the opening in the hook so that the end of the fishing line performed at 15 cm.
2. Further, the fore-end wrap the fishing line in the 5-12 turns. The coils should be stacked side by side, to avoid overlaps.
3. Then the end of the fishing line is passed through the first loop.
4. Pull the end of the fishing line so as to obtain a node.
5. Expand the node and then tighten. The excess fishing line is cut off, thus it is necessary to leave the tip length of 4 millimeters.

knotless node

This method of attachment will be interesting to every angler because node node-free very strong hook, and it is always possible to catch large quantities of fish.

As the node-free tie the knot?

1. First, you need to make the hair rig. To do this, take a piece flanged material, while its length must be given twice. If you are using monofilament type Snake, a cover is moved and a driving material is laid bare by 15 cm.
2. Then tied a simple knot at one end of the leash (left to right).
3. After that you want to skip the line or leash through the hole in the hook. It is desirable that the tip with a loop was placed on top of the curved side of the hook, a free end of the fishing line must be threaded through a hole in the hook. Monofilament tightened by means of the free end to the desired length.
4. The free end of the fishing line wrapped around the hook.
5. In the end it is necessary to push back the free end of the hook into the hole and tighten tight.

Polomar

It is kind of knotless knot. Nodes of this type are used for hook with eyelet, it is desirable to use a hook with a large eye.

Tying this knot is as follows:

• Lesko need to be folded in half.
• Then thread the loop through the eye in the hook.
• Next, make a loop out of the main line and pull it through the end of the fishing line folded.
• After that spreads loop through the hook so that she was on an ear and not on the shank of the hook.
• In the end you need to tighten the knot, and the remnants of the fishing line cut.

To fasten the components to hook quite simple, and probably any novice angler will understand in this scheme easily.

Clinch improved

This node also relates to a knotless mount. tying scheme is very simple. If these nodes for the hook to do it right, you will eventually get a strong tackle, on which you can catch large amounts of fish.

In order to tie the improved clinch, should do the following:

1. The first step is to thread the end of the fishing line through the hole in the hook and followed to make 6 turns around the main line.
2. Further, the resulting loop around ringlet hook tip must thread the fishing line. After that, the line is threaded in a loop, which was made in the previous step.
3. At the end of the fishing line damp to avoid its heating or different strains, further delaying the fishing line. Cut the excess part of all - the improved clinch ready.